(gdb.info.gz) GDB/MI Data Manipulation
Info Catalog
(gdb.info.gz) GDB/MI Variable Objects
(gdb.info.gz) GDB/MI
(gdb.info.gz) GDB/MI Tracepoint Commands
27.14 GDB/MI Data Manipulation
==============================
This section describes the GDB/MI commands that manipulate data:
examine memory and registers, evaluate expressions, etc.
The `-data-disassemble' Command
-------------------------------
Synopsis
........
-data-disassemble
[ -s START-ADDR -e END-ADDR ]
| [ -f FILENAME -l LINENUM [ -n LINES ] ]
-- MODE
Where:
`START-ADDR'
is the beginning address (or `$pc')
`END-ADDR'
is the end address
`FILENAME'
is the name of the file to disassemble
`LINENUM'
is the line number to disassemble around
`LINES'
is the number of disassembly lines to be produced. If it is -1,
the whole function will be disassembled, in case no END-ADDR is
specified. If END-ADDR is specified as a non-zero value, and
LINES is lower than the number of disassembly lines between
START-ADDR and END-ADDR, only LINES lines are displayed; if LINES
is higher than the number of lines between START-ADDR and
END-ADDR, only the lines up to END-ADDR are displayed.
`MODE'
is either 0 (meaning only disassembly) or 1 (meaning mixed source
and disassembly).
Result
......
The output for each instruction is composed of four fields:
* Address
* Func-name
* Offset
* Instruction
Note that whatever included in the instruction field, is not
manipulated directly by GDB/MI, i.e., it is not possible to adjust its
format.
GDB Command
...........
There's no direct mapping from this command to the CLI.
Example
.......
Disassemble from the current value of `$pc' to `$pc + 20':
(gdb)
-data-disassemble -s $pc -e "$pc + 20" -- 0
^done,
asm_insns=[
{address="0x000107c0",func-name="main",offset="4",
inst="mov 2, %o0"},
{address="0x000107c4",func-name="main",offset="8",
inst="sethi %hi(0x11800), %o2"},
{address="0x000107c8",func-name="main",offset="12",
inst="or %o2, 0x140, %o1\t! 0x11940 <_lib_version+8>"},
{address="0x000107cc",func-name="main",offset="16",
inst="sethi %hi(0x11800), %o2"},
{address="0x000107d0",func-name="main",offset="20",
inst="or %o2, 0x168, %o4\t! 0x11968 <_lib_version+48>"}]
(gdb)
Disassemble the whole `main' function. Line 32 is part of `main'.
-data-disassemble -f basics.c -l 32 -- 0
^done,asm_insns=[
{address="0x000107bc",func-name="main",offset="0",
inst="save %sp, -112, %sp"},
{address="0x000107c0",func-name="main",offset="4",
inst="mov 2, %o0"},
{address="0x000107c4",func-name="main",offset="8",
inst="sethi %hi(0x11800), %o2"},
[...]
{address="0x0001081c",func-name="main",offset="96",inst="ret "},
{address="0x00010820",func-name="main",offset="100",inst="restore "}]
(gdb)
Disassemble 3 instructions from the start of `main':
(gdb)
-data-disassemble -f basics.c -l 32 -n 3 -- 0
^done,asm_insns=[
{address="0x000107bc",func-name="main",offset="0",
inst="save %sp, -112, %sp"},
{address="0x000107c0",func-name="main",offset="4",
inst="mov 2, %o0"},
{address="0x000107c4",func-name="main",offset="8",
inst="sethi %hi(0x11800), %o2"}]
(gdb)
Disassemble 3 instructions from the start of `main' in mixed mode:
(gdb)
-data-disassemble -f basics.c -l 32 -n 3 -- 1
^done,asm_insns=[
src_and_asm_line={line="31",
file="/kwikemart/marge/ezannoni/flathead-dev/devo/gdb/ \
testsuite/gdb.mi/basics.c",line_asm_insn=[
{address="0x000107bc",func-name="main",offset="0",
inst="save %sp, -112, %sp"}]},
src_and_asm_line={line="32",
file="/kwikemart/marge/ezannoni/flathead-dev/devo/gdb/ \
testsuite/gdb.mi/basics.c",line_asm_insn=[
{address="0x000107c0",func-name="main",offset="4",
inst="mov 2, %o0"},
{address="0x000107c4",func-name="main",offset="8",
inst="sethi %hi(0x11800), %o2"}]}]
(gdb)
The `-data-evaluate-expression' Command
---------------------------------------
Synopsis
........
-data-evaluate-expression EXPR
Evaluate EXPR as an expression. The expression could contain an
inferior function call. The function call will execute synchronously.
If the expression contains spaces, it must be enclosed in double quotes.
GDB Command
...........
The corresponding GDB commands are `print', `output', and `call'. In
`gdbtk' only, there's a corresponding `gdb_eval' command.
Example
.......
In the following example, the numbers that precede the commands are the
"tokens" described in GDB/MI Command Syntax GDB/MI Command
Syntax. Notice how GDB/MI returns the same tokens in its output.
211-data-evaluate-expression A
211^done,value="1"
(gdb)
311-data-evaluate-expression &A
311^done,value="0xefffeb7c"
(gdb)
411-data-evaluate-expression A+3
411^done,value="4"
(gdb)
511-data-evaluate-expression "A + 3"
511^done,value="4"
(gdb)
The `-data-list-changed-registers' Command
------------------------------------------
Synopsis
........
-data-list-changed-registers
Display a list of the registers that have changed.
GDB Command
...........
GDB doesn't have a direct analog for this command; `gdbtk' has the
corresponding command `gdb_changed_register_list'.
Example
.......
On a PPC MBX board:
(gdb)
-exec-continue
^running
(gdb)
*stopped,reason="breakpoint-hit",disp="keep",bkptno="1",frame={
func="main",args=[],file="try.c",fullname="/home/foo/bar/try.c",
line="5"}
(gdb)
-data-list-changed-registers
^done,changed-registers=["0","1","2","4","5","6","7","8","9",
"10","11","13","14","15","16","17","18","19","20","21","22","23",
"24","25","26","27","28","30","31","64","65","66","67","69"]
(gdb)
The `-data-list-register-names' Command
---------------------------------------
Synopsis
........
-data-list-register-names [ ( REGNO )+ ]
Show a list of register names for the current target. If no
arguments are given, it shows a list of the names of all the registers.
If integer numbers are given as arguments, it will print a list of the
names of the registers corresponding to the arguments. To ensure
consistency between a register name and its number, the output list may
include empty register names.
GDB Command
...........
GDB does not have a command which corresponds to
`-data-list-register-names'. In `gdbtk' there is a corresponding
command `gdb_regnames'.
Example
.......
For the PPC MBX board:
(gdb)
-data-list-register-names
^done,register-names=["r0","r1","r2","r3","r4","r5","r6","r7",
"r8","r9","r10","r11","r12","r13","r14","r15","r16","r17","r18",
"r19","r20","r21","r22","r23","r24","r25","r26","r27","r28","r29",
"r30","r31","f0","f1","f2","f3","f4","f5","f6","f7","f8","f9",
"f10","f11","f12","f13","f14","f15","f16","f17","f18","f19","f20",
"f21","f22","f23","f24","f25","f26","f27","f28","f29","f30","f31",
"", "pc","ps","cr","lr","ctr","xer"]
(gdb)
-data-list-register-names 1 2 3
^done,register-names=["r1","r2","r3"]
(gdb)
The `-data-list-register-values' Command
----------------------------------------
Synopsis
........
-data-list-register-values FMT [ ( REGNO )*]
Display the registers' contents. FMT is the format according to
which the registers' contents are to be returned, followed by an
optional list of numbers specifying the registers to display. A
missing list of numbers indicates that the contents of all the
registers must be returned.
Allowed formats for FMT are:
`x'
Hexadecimal
`o'
Octal
`t'
Binary
`d'
Decimal
`r'
Raw
`N'
Natural
GDB Command
...........
The corresponding GDB commands are `info reg', `info all-reg', and (in
`gdbtk') `gdb_fetch_registers'.
Example
.......
For a PPC MBX board (note: line breaks are for readability only, they
don't appear in the actual output):
(gdb)
-data-list-register-values r 64 65
^done,register-values=[{number="64",value="0xfe00a300"},
{number="65",value="0x00029002"}]
(gdb)
-data-list-register-values x
^done,register-values=[{number="0",value="0xfe0043c8"},
{number="1",value="0x3fff88"},{number="2",value="0xfffffffe"},
{number="3",value="0x0"},{number="4",value="0xa"},
{number="5",value="0x3fff68"},{number="6",value="0x3fff58"},
{number="7",value="0xfe011e98"},{number="8",value="0x2"},
{number="9",value="0xfa202820"},{number="10",value="0xfa202808"},
{number="11",value="0x1"},{number="12",value="0x0"},
{number="13",value="0x4544"},{number="14",value="0xffdfffff"},
{number="15",value="0xffffffff"},{number="16",value="0xfffffeff"},
{number="17",value="0xefffffed"},{number="18",value="0xfffffffe"},
{number="19",value="0xffffffff"},{number="20",value="0xffffffff"},
{number="21",value="0xffffffff"},{number="22",value="0xfffffff7"},
{number="23",value="0xffffffff"},{number="24",value="0xffffffff"},
{number="25",value="0xffffffff"},{number="26",value="0xfffffffb"},
{number="27",value="0xffffffff"},{number="28",value="0xf7bfffff"},
{number="29",value="0x0"},{number="30",value="0xfe010000"},
{number="31",value="0x0"},{number="32",value="0x0"},
{number="33",value="0x0"},{number="34",value="0x0"},
{number="35",value="0x0"},{number="36",value="0x0"},
{number="37",value="0x0"},{number="38",value="0x0"},
{number="39",value="0x0"},{number="40",value="0x0"},
{number="41",value="0x0"},{number="42",value="0x0"},
{number="43",value="0x0"},{number="44",value="0x0"},
{number="45",value="0x0"},{number="46",value="0x0"},
{number="47",value="0x0"},{number="48",value="0x0"},
{number="49",value="0x0"},{number="50",value="0x0"},
{number="51",value="0x0"},{number="52",value="0x0"},
{number="53",value="0x0"},{number="54",value="0x0"},
{number="55",value="0x0"},{number="56",value="0x0"},
{number="57",value="0x0"},{number="58",value="0x0"},
{number="59",value="0x0"},{number="60",value="0x0"},
{number="61",value="0x0"},{number="62",value="0x0"},
{number="63",value="0x0"},{number="64",value="0xfe00a300"},
{number="65",value="0x29002"},{number="66",value="0x202f04b5"},
{number="67",value="0xfe0043b0"},{number="68",value="0xfe00b3e4"},
{number="69",value="0x20002b03"}]
(gdb)
The `-data-read-memory' Command
-------------------------------
Synopsis
........
-data-read-memory [ -o BYTE-OFFSET ]
ADDRESS WORD-FORMAT WORD-SIZE
NR-ROWS NR-COLS [ ASCHAR ]
where:
`ADDRESS'
An expression specifying the address of the first memory word to be
read. Complex expressions containing embedded white space should
be quoted using the C convention.
`WORD-FORMAT'
The format to be used to print the memory words. The notation is
the same as for GDB's `print' command ( Output Formats
Output Formats.).
`WORD-SIZE'
The size of each memory word in bytes.
`NR-ROWS'
The number of rows in the output table.
`NR-COLS'
The number of columns in the output table.
`ASCHAR'
If present, indicates that each row should include an ASCII dump.
The value of ASCHAR is used as a padding character when a byte is
not a member of the printable ASCII character set (printable ASCII
characters are those whose code is between 32 and 126,
inclusively).
`BYTE-OFFSET'
An offset to add to the ADDRESS before fetching memory.
This command displays memory contents as a table of NR-ROWS by
NR-COLS words, each word being WORD-SIZE bytes. In total, `NR-ROWS *
NR-COLS * WORD-SIZE' bytes are read (returned as `total-bytes').
Should less than the requested number of bytes be returned by the
target, the missing words are identified using `N/A'. The number of
bytes read from the target is returned in `nr-bytes' and the starting
address used to read memory in `addr'.
The address of the next/previous row or page is available in
`next-row' and `prev-row', `next-page' and `prev-page'.
GDB Command
...........
The corresponding GDB command is `x'. `gdbtk' has `gdb_get_mem' memory
read command.
Example
.......
Read six bytes of memory starting at `bytes+6' but then offset by `-6'
bytes. Format as three rows of two columns. One byte per word.
Display each word in hex.
(gdb)
9-data-read-memory -o -6 -- bytes+6 x 1 3 2
9^done,addr="0x00001390",nr-bytes="6",total-bytes="6",
next-row="0x00001396",prev-row="0x0000138e",next-page="0x00001396",
prev-page="0x0000138a",memory=[
{addr="0x00001390",data=["0x00","0x01"]},
{addr="0x00001392",data=["0x02","0x03"]},
{addr="0x00001394",data=["0x04","0x05"]}]
(gdb)
Read two bytes of memory starting at address `shorts + 64' and
display as a single word formatted in decimal.
(gdb)
5-data-read-memory shorts+64 d 2 1 1
5^done,addr="0x00001510",nr-bytes="2",total-bytes="2",
next-row="0x00001512",prev-row="0x0000150e",
next-page="0x00001512",prev-page="0x0000150e",memory=[
{addr="0x00001510",data=["128"]}]
(gdb)
Read thirty two bytes of memory starting at `bytes+16' and format as
eight rows of four columns. Include a string encoding with `x' used as
the non-printable character.
(gdb)
4-data-read-memory bytes+16 x 1 8 4 x
4^done,addr="0x000013a0",nr-bytes="32",total-bytes="32",
next-row="0x000013c0",prev-row="0x0000139c",
next-page="0x000013c0",prev-page="0x00001380",memory=[
{addr="0x000013a0",data=["0x10","0x11","0x12","0x13"],ascii="xxxx"},
{addr="0x000013a4",data=["0x14","0x15","0x16","0x17"],ascii="xxxx"},
{addr="0x000013a8",data=["0x18","0x19","0x1a","0x1b"],ascii="xxxx"},
{addr="0x000013ac",data=["0x1c","0x1d","0x1e","0x1f"],ascii="xxxx"},
{addr="0x000013b0",data=["0x20","0x21","0x22","0x23"],ascii=" !\"#"},
{addr="0x000013b4",data=["0x24","0x25","0x26","0x27"],ascii="$%&'"},
{addr="0x000013b8",data=["0x28","0x29","0x2a","0x2b"],ascii="()*+"},
{addr="0x000013bc",data=["0x2c","0x2d","0x2e","0x2f"],ascii=",-./"}]
(gdb)
Info Catalog
(gdb.info.gz) GDB/MI Variable Objects
(gdb.info.gz) GDB/MI
(gdb.info.gz) GDB/MI Tracepoint Commands
automatically generated by
info2html