(gcc.info) RS/6000 and PowerPC Options
Info Catalog
(gcc.info) PowerPC Options
(gcc.info) Submodel Options
(gcc.info) S/390 and zSeries Options
3.17.29 IBM RS/6000 and PowerPC Options
---------------------------------------
These `-m' options are defined for the IBM RS/6000 and PowerPC:
`-mpower'
`-mno-power'
`-mpower2'
`-mno-power2'
`-mpowerpc'
`-mno-powerpc'
`-mpowerpc-gpopt'
`-mno-powerpc-gpopt'
`-mpowerpc-gfxopt'
`-mno-powerpc-gfxopt'
`-mpowerpc64'
`-mno-powerpc64'
`-mmfcrf'
`-mno-mfcrf'
`-mpopcntb'
`-mno-popcntb'
`-mpopcntd'
`-mno-popcntd'
`-mfprnd'
`-mno-fprnd'
`-mcmpb'
`-mno-cmpb'
`-mmfpgpr'
`-mno-mfpgpr'
`-mhard-dfp'
`-mno-hard-dfp'
GCC supports two related instruction set architectures for the
RS/6000 and PowerPC. The "POWER" instruction set are those
instructions supported by the `rios' chip set used in the original
RS/6000 systems and the "PowerPC" instruction set is the
architecture of the Freescale MPC5xx, MPC6xx, MPC8xx
microprocessors, and the IBM 4xx, 6xx, and follow-on
microprocessors.
Neither architecture is a subset of the other. However there is a
large common subset of instructions supported by both. An MQ
register is included in processors supporting the POWER
architecture.
You use these options to specify which instructions are available
on the processor you are using. The default value of these
options is determined when configuring GCC. Specifying the
`-mcpu=CPU_TYPE' overrides the specification of these options. We
recommend you use the `-mcpu=CPU_TYPE' option rather than the
options listed above.
The `-mpower' option allows GCC to generate instructions that are
found only in the POWER architecture and to use the MQ register.
Specifying `-mpower2' implies `-power' and also allows GCC to
generate instructions that are present in the POWER2 architecture
but not the original POWER architecture.
The `-mpowerpc' option allows GCC to generate instructions that
are found only in the 32-bit subset of the PowerPC architecture.
Specifying `-mpowerpc-gpopt' implies `-mpowerpc' and also allows
GCC to use the optional PowerPC architecture instructions in the
General Purpose group, including floating-point square root.
Specifying `-mpowerpc-gfxopt' implies `-mpowerpc' and also allows
GCC to use the optional PowerPC architecture instructions in the
Graphics group, including floating-point select.
The `-mmfcrf' option allows GCC to generate the move from
condition register field instruction implemented on the POWER4
processor and other processors that support the PowerPC V2.01
architecture. The `-mpopcntb' option allows GCC to generate the
popcount and double precision FP reciprocal estimate instruction
implemented on the POWER5 processor and other processors that
support the PowerPC V2.02 architecture. The `-mpopcntd' option
allows GCC to generate the popcount instruction implemented on the
POWER7 processor and other processors that support the PowerPC
V2.06 architecture. The `-mfprnd' option allows GCC to generate
the FP round to integer instructions implemented on the POWER5+
processor and other processors that support the PowerPC V2.03
architecture. The `-mcmpb' option allows GCC to generate the
compare bytes instruction implemented on the POWER6 processor and
other processors that support the PowerPC V2.05 architecture. The
`-mmfpgpr' option allows GCC to generate the FP move to/from
general purpose register instructions implemented on the POWER6X
processor and other processors that support the extended PowerPC
V2.05 architecture. The `-mhard-dfp' option allows GCC to
generate the decimal floating point instructions implemented on
some POWER processors.
The `-mpowerpc64' option allows GCC to generate the additional
64-bit instructions that are found in the full PowerPC64
architecture and to treat GPRs as 64-bit, doubleword quantities.
GCC defaults to `-mno-powerpc64'.
If you specify both `-mno-power' and `-mno-powerpc', GCC will use
only the instructions in the common subset of both architectures
plus some special AIX common-mode calls, and will not use the MQ
register. Specifying both `-mpower' and `-mpowerpc' permits GCC
to use any instruction from either architecture and to allow use
of the MQ register; specify this for the Motorola MPC601.
`-mnew-mnemonics'
`-mold-mnemonics'
Select which mnemonics to use in the generated assembler code.
With `-mnew-mnemonics', GCC uses the assembler mnemonics defined
for the PowerPC architecture. With `-mold-mnemonics' it uses the
assembler mnemonics defined for the POWER architecture.
Instructions defined in only one architecture have only one
mnemonic; GCC uses that mnemonic irrespective of which of these
options is specified.
GCC defaults to the mnemonics appropriate for the architecture in
use. Specifying `-mcpu=CPU_TYPE' sometimes overrides the value of
these option. Unless you are building a cross-compiler, you
should normally not specify either `-mnew-mnemonics' or
`-mold-mnemonics', but should instead accept the default.
`-mcpu=CPU_TYPE'
Set architecture type, register usage, choice of mnemonics, and
instruction scheduling parameters for machine type CPU_TYPE.
Supported values for CPU_TYPE are `401', `403', `405', `405fp',
`440', `440fp', `464', `464fp', `505', `601', `602', `603',
`603e', `604', `604e', `620', `630', `740', `7400', `7450', `750',
`801', `821', `823', `860', `970', `8540', `e300c2', `e300c3',
`e500mc', `ec603e', `G3', `G4', `G5', `power', `power2', `power3',
`power4', `power5', `power5+', `power6', `power6x', `power7',
`common', `powerpc', `powerpc64', `rios', `rios1', `rios2', `rsc',
and `rs64'.
`-mcpu=common' selects a completely generic processor. Code
generated under this option will run on any POWER or PowerPC
processor. GCC will use only the instructions in the common
subset of both architectures, and will not use the MQ register.
GCC assumes a generic processor model for scheduling purposes.
`-mcpu=power', `-mcpu=power2', `-mcpu=powerpc', and
`-mcpu=powerpc64' specify generic POWER, POWER2, pure 32-bit
PowerPC (i.e., not MPC601), and 64-bit PowerPC architecture machine
types, with an appropriate, generic processor model assumed for
scheduling purposes.
The other options specify a specific processor. Code generated
under those options will run best on that processor, and may not
run at all on others.
The `-mcpu' options automatically enable or disable the following
options:
-maltivec -mfprnd -mhard-float -mmfcrf -mmultiple
-mnew-mnemonics -mpopcntb -mpopcntd -mpower -mpower2 -mpowerpc64
-mpowerpc-gpopt -mpowerpc-gfxopt -msingle-float -mdouble-float
-msimple-fpu -mstring -mmulhw -mdlmzb -mmfpgpr -mvsx
The particular options set for any particular CPU will vary between
compiler versions, depending on what setting seems to produce
optimal code for that CPU; it doesn't necessarily reflect the
actual hardware's capabilities. If you wish to set an individual
option to a particular value, you may specify it after the `-mcpu'
option, like `-mcpu=970 -mno-altivec'.
On AIX, the `-maltivec' and `-mpowerpc64' options are not enabled
or disabled by the `-mcpu' option at present because AIX does not
have full support for these options. You may still enable or
disable them individually if you're sure it'll work in your
environment.
`-mtune=CPU_TYPE'
Set the instruction scheduling parameters for machine type
CPU_TYPE, but do not set the architecture type, register usage, or
choice of mnemonics, as `-mcpu=CPU_TYPE' would. The same values
for CPU_TYPE are used for `-mtune' as for `-mcpu'. If both are
specified, the code generated will use the architecture,
registers, and mnemonics set by `-mcpu', but the scheduling
parameters set by `-mtune'.
`-mcmodel=small'
Generate PowerPC64 code for the small model: The TOC is limited to
64k.
`-mcmodel=medium'
Generate PowerPC64 code for the medium model: The TOC and other
static data may be up to a total of 4G in size.
`-mcmodel=large'
Generate PowerPC64 code for the large model: The TOC may be up to
4G in size. Other data and code is only limited by the 64-bit
address space.
`-mswdiv'
`-mno-swdiv'
Generate code to compute division as reciprocal estimate and
iterative refinement, creating opportunities for increased
throughput. This feature requires: optional PowerPC Graphics
instruction set for single precision and FRE instruction for
double precision, assuming divides cannot generate user-visible
traps, and the domain values not include Infinities, denormals or
zero denominator.
`-maltivec'
`-mno-altivec'
Generate code that uses (does not use) AltiVec instructions, and
also enable the use of built-in functions that allow more direct
access to the AltiVec instruction set. You may also need to set
`-mabi=altivec' to adjust the current ABI with AltiVec ABI
enhancements.
`-mvrsave'
`-mno-vrsave'
Generate VRSAVE instructions when generating AltiVec code.
`-mgen-cell-microcode'
Generate Cell microcode instructions
`-mwarn-cell-microcode'
Warning when a Cell microcode instruction is going to emitted. An
example of a Cell microcode instruction is a variable shift.
`-msecure-plt'
Generate code that allows ld and ld.so to build executables and
shared libraries with non-exec .plt and .got sections. This is a
PowerPC 32-bit SYSV ABI option.
`-mbss-plt'
Generate code that uses a BSS .plt section that ld.so fills in, and
requires .plt and .got sections that are both writable and
executable. This is a PowerPC 32-bit SYSV ABI option.
`-misel'
`-mno-isel'
This switch enables or disables the generation of ISEL
instructions.
`-misel=YES/NO'
This switch has been deprecated. Use `-misel' and `-mno-isel'
instead.
`-mspe'
`-mno-spe'
This switch enables or disables the generation of SPE simd
instructions.
`-mpaired'
`-mno-paired'
This switch enables or disables the generation of PAIRED simd
instructions.
`-mspe=YES/NO'
This option has been deprecated. Use `-mspe' and `-mno-spe'
instead.
`-mvsx'
`-mno-vsx'
Generate code that uses (does not use) vector/scalar (VSX)
instructions, and also enable the use of built-in functions that
allow more direct access to the VSX instruction set.
`-mfloat-gprs=YES/SINGLE/DOUBLE/NO'
`-mfloat-gprs'
This switch enables or disables the generation of floating point
operations on the general purpose registers for architectures that
support it.
The argument YES or SINGLE enables the use of single-precision
floating point operations.
The argument DOUBLE enables the use of single and double-precision
floating point operations.
The argument NO disables floating point operations on the general
purpose registers.
This option is currently only available on the MPC854x.
`-m32'
`-m64'
Generate code for 32-bit or 64-bit environments of Darwin and SVR4
targets (including GNU/Linux). The 32-bit environment sets int,
long and pointer to 32 bits and generates code that runs on any
PowerPC variant. The 64-bit environment sets int to 32 bits and
long and pointer to 64 bits, and generates code for PowerPC64, as
for `-mpowerpc64'.
`-mfull-toc'
`-mno-fp-in-toc'
`-mno-sum-in-toc'
`-mminimal-toc'
Modify generation of the TOC (Table Of Contents), which is created
for every executable file. The `-mfull-toc' option is selected by
default. In that case, GCC will allocate at least one TOC entry
for each unique non-automatic variable reference in your program.
GCC will also place floating-point constants in the TOC. However,
only 16,384 entries are available in the TOC.
If you receive a linker error message that saying you have
overflowed the available TOC space, you can reduce the amount of
TOC space used with the `-mno-fp-in-toc' and `-mno-sum-in-toc'
options. `-mno-fp-in-toc' prevents GCC from putting floating-point
constants in the TOC and `-mno-sum-in-toc' forces GCC to generate
code to calculate the sum of an address and a constant at run-time
instead of putting that sum into the TOC. You may specify one or
both of these options. Each causes GCC to produce very slightly
slower and larger code at the expense of conserving TOC space.
If you still run out of space in the TOC even when you specify
both of these options, specify `-mminimal-toc' instead. This
option causes GCC to make only one TOC entry for every file. When
you specify this option, GCC will produce code that is slower and
larger but which uses extremely little TOC space. You may wish to
use this option only on files that contain less frequently
executed code.
`-maix64'
`-maix32'
Enable 64-bit AIX ABI and calling convention: 64-bit pointers,
64-bit `long' type, and the infrastructure needed to support them.
Specifying `-maix64' implies `-mpowerpc64' and `-mpowerpc', while
`-maix32' disables the 64-bit ABI and implies `-mno-powerpc64'.
GCC defaults to `-maix32'.
`-mxl-compat'
`-mno-xl-compat'
Produce code that conforms more closely to IBM XL compiler
semantics when using AIX-compatible ABI. Pass floating-point
arguments to prototyped functions beyond the register save area
(RSA) on the stack in addition to argument FPRs. Do not assume
that most significant double in 128-bit long double value is
properly rounded when comparing values and converting to double.
Use XL symbol names for long double support routines.
The AIX calling convention was extended but not initially
documented to handle an obscure K&R C case of calling a function
that takes the address of its arguments with fewer arguments than
declared. IBM XL compilers access floating point arguments which
do not fit in the RSA from the stack when a subroutine is compiled
without optimization. Because always storing floating-point
arguments on the stack is inefficient and rarely needed, this
option is not enabled by default and only is necessary when
calling subroutines compiled by IBM XL compilers without
optimization.
`-mpe'
Support "IBM RS/6000 SP" "Parallel Environment" (PE). Link an
application written to use message passing with special startup
code to enable the application to run. The system must have PE
installed in the standard location (`/usr/lpp/ppe.poe/'), or the
`specs' file must be overridden with the `-specs=' option to
specify the appropriate directory location. The Parallel
Environment does not support threads, so the `-mpe' option and the
`-pthread' option are incompatible.
`-malign-natural'
`-malign-power'
On AIX, 32-bit Darwin, and 64-bit PowerPC GNU/Linux, the option
`-malign-natural' overrides the ABI-defined alignment of larger
types, such as floating-point doubles, on their natural size-based
boundary. The option `-malign-power' instructs GCC to follow the
ABI-specified alignment rules. GCC defaults to the standard
alignment defined in the ABI.
On 64-bit Darwin, natural alignment is the default, and
`-malign-power' is not supported.
`-msoft-float'
`-mhard-float'
Generate code that does not use (uses) the floating-point register
set. Software floating point emulation is provided if you use the
`-msoft-float' option, and pass the option to GCC when linking.
`-msingle-float'
`-mdouble-float'
Generate code for single or double-precision floating point
operations. `-mdouble-float' implies `-msingle-float'.
`-msimple-fpu'
Do not generate sqrt and div instructions for hardware floating
point unit.
`-mfpu'
Specify type of floating point unit. Valid values are SP_LITE
(equivalent to -msingle-float -msimple-fpu), DP_LITE (equivalent
to -mdouble-float -msimple-fpu), SP_FULL (equivalent to
-msingle-float), and DP_FULL (equivalent to -mdouble-float).
`-mxilinx-fpu'
Perform optimizations for floating point unit on Xilinx PPC
405/440.
`-mmultiple'
`-mno-multiple'
Generate code that uses (does not use) the load multiple word
instructions and the store multiple word instructions. These
instructions are generated by default on POWER systems, and not
generated on PowerPC systems. Do not use `-mmultiple' on little
endian PowerPC systems, since those instructions do not work when
the processor is in little endian mode. The exceptions are PPC740
and PPC750 which permit the instructions usage in little endian
mode.
`-mstring'
`-mno-string'
Generate code that uses (does not use) the load string instructions
and the store string word instructions to save multiple registers
and do small block moves. These instructions are generated by
default on POWER systems, and not generated on PowerPC systems.
Do not use `-mstring' on little endian PowerPC systems, since those
instructions do not work when the processor is in little endian
mode. The exceptions are PPC740 and PPC750 which permit the
instructions usage in little endian mode.
`-mupdate'
`-mno-update'
Generate code that uses (does not use) the load or store
instructions that update the base register to the address of the
calculated memory location. These instructions are generated by
default. If you use `-mno-update', there is a small window
between the time that the stack pointer is updated and the address
of the previous frame is stored, which means code that walks the
stack frame across interrupts or signals may get corrupted data.
`-mavoid-indexed-addresses'
`-mno-avoid-indexed-addresses'
Generate code that tries to avoid (not avoid) the use of indexed
load or store instructions. These instructions can incur a
performance penalty on Power6 processors in certain situations,
such as when stepping through large arrays that cross a 16M
boundary. This option is enabled by default when targetting
Power6 and disabled otherwise.
`-mfused-madd'
`-mno-fused-madd'
Generate code that uses (does not use) the floating point multiply
and accumulate instructions. These instructions are generated by
default if hardware floating is used.
`-mmulhw'
`-mno-mulhw'
Generate code that uses (does not use) the half-word multiply and
multiply-accumulate instructions on the IBM 405, 440 and 464
processors. These instructions are generated by default when
targetting those processors.
`-mdlmzb'
`-mno-dlmzb'
Generate code that uses (does not use) the string-search `dlmzb'
instruction on the IBM 405, 440 and 464 processors. This
instruction is generated by default when targetting those
processors.
`-mno-bit-align'
`-mbit-align'
On System V.4 and embedded PowerPC systems do not (do) force
structures and unions that contain bit-fields to be aligned to the
base type of the bit-field.
For example, by default a structure containing nothing but 8
`unsigned' bit-fields of length 1 would be aligned to a 4 byte
boundary and have a size of 4 bytes. By using `-mno-bit-align',
the structure would be aligned to a 1 byte boundary and be one
byte in size.
`-mno-strict-align'
`-mstrict-align'
On System V.4 and embedded PowerPC systems do not (do) assume that
unaligned memory references will be handled by the system.
`-mrelocatable'
`-mno-relocatable'
On embedded PowerPC systems generate code that allows (does not
allow) the program to be relocated to a different address at
runtime. If you use `-mrelocatable' on any module, all objects
linked together must be compiled with `-mrelocatable' or
`-mrelocatable-lib'.
`-mrelocatable-lib'
`-mno-relocatable-lib'
On embedded PowerPC systems generate code that allows (does not
allow) the program to be relocated to a different address at
runtime. Modules compiled with `-mrelocatable-lib' can be linked
with either modules compiled without `-mrelocatable' and
`-mrelocatable-lib' or with modules compiled with the
`-mrelocatable' options.
`-mno-toc'
`-mtoc'
On System V.4 and embedded PowerPC systems do not (do) assume that
register 2 contains a pointer to a global area pointing to the
addresses used in the program.
`-mlittle'
`-mlittle-endian'
On System V.4 and embedded PowerPC systems compile code for the
processor in little endian mode. The `-mlittle-endian' option is
the same as `-mlittle'.
`-mbig'
`-mbig-endian'
On System V.4 and embedded PowerPC systems compile code for the
processor in big endian mode. The `-mbig-endian' option is the
same as `-mbig'.
`-mdynamic-no-pic'
On Darwin and Mac OS X systems, compile code so that it is not
relocatable, but that its external references are relocatable. The
resulting code is suitable for applications, but not shared
libraries.
`-mprioritize-restricted-insns=PRIORITY'
This option controls the priority that is assigned to
dispatch-slot restricted instructions during the second scheduling
pass. The argument PRIORITY takes the value 0/1/2 to assign
NO/HIGHEST/SECOND-HIGHEST priority to dispatch slot restricted
instructions.
`-msched-costly-dep=DEPENDENCE_TYPE'
This option controls which dependences are considered costly by
the target during instruction scheduling. The argument
DEPENDENCE_TYPE takes one of the following values: NO: no
dependence is costly, ALL: all dependences are costly,
TRUE_STORE_TO_LOAD: a true dependence from store to load is costly,
STORE_TO_LOAD: any dependence from store to load is costly,
NUMBER: any dependence which latency >= NUMBER is costly.
`-minsert-sched-nops=SCHEME'
This option controls which nop insertion scheme will be used during
the second scheduling pass. The argument SCHEME takes one of the
following values: NO: Don't insert nops. PAD: Pad with nops any
dispatch group which has vacant issue slots, according to the
scheduler's grouping. REGROUP_EXACT: Insert nops to force costly
dependent insns into separate groups. Insert exactly as many nops
as needed to force an insn to a new group, according to the
estimated processor grouping. NUMBER: Insert nops to force costly
dependent insns into separate groups. Insert NUMBER nops to force
an insn to a new group.
`-mcall-sysv'
On System V.4 and embedded PowerPC systems compile code using
calling conventions that adheres to the March 1995 draft of the
System V Application Binary Interface, PowerPC processor
supplement. This is the default unless you configured GCC using
`powerpc-*-eabiaix'.
`-mcall-sysv-eabi'
Specify both `-mcall-sysv' and `-meabi' options.
`-mcall-sysv-noeabi'
Specify both `-mcall-sysv' and `-mno-eabi' options.
`-mcall-solaris'
On System V.4 and embedded PowerPC systems compile code for the
Solaris operating system.
`-mcall-linux'
On System V.4 and embedded PowerPC systems compile code for the
Linux-based GNU system.
`-mcall-gnu'
On System V.4 and embedded PowerPC systems compile code for the
Hurd-based GNU system.
`-mcall-netbsd'
On System V.4 and embedded PowerPC systems compile code for the
NetBSD operating system.
`-maix-struct-return'
Return all structures in memory (as specified by the AIX ABI).
`-msvr4-struct-return'
Return structures smaller than 8 bytes in registers (as specified
by the SVR4 ABI).
`-mabi=ABI-TYPE'
Extend the current ABI with a particular extension, or remove such
extension. Valid values are ALTIVEC, NO-ALTIVEC, SPE, NO-SPE,
IBMLONGDOUBLE, IEEELONGDOUBLE.
`-mabi=spe'
Extend the current ABI with SPE ABI extensions. This does not
change the default ABI, instead it adds the SPE ABI extensions to
the current ABI.
`-mabi=no-spe'
Disable Booke SPE ABI extensions for the current ABI.
`-mabi=ibmlongdouble'
Change the current ABI to use IBM extended precision long double.
This is a PowerPC 32-bit SYSV ABI option.
`-mabi=ieeelongdouble'
Change the current ABI to use IEEE extended precision long double.
This is a PowerPC 32-bit Linux ABI option.
`-mprototype'
`-mno-prototype'
On System V.4 and embedded PowerPC systems assume that all calls to
variable argument functions are properly prototyped. Otherwise,
the compiler must insert an instruction before every non
prototyped call to set or clear bit 6 of the condition code
register (CR) to indicate whether floating point values were
passed in the floating point registers in case the function takes
a variable arguments. With `-mprototype', only calls to
prototyped variable argument functions will set or clear the bit.
`-msim'
On embedded PowerPC systems, assume that the startup module is
called `sim-crt0.o' and that the standard C libraries are
`libsim.a' and `libc.a'. This is the default for
`powerpc-*-eabisim' configurations.
`-mmvme'
On embedded PowerPC systems, assume that the startup module is
called `crt0.o' and the standard C libraries are `libmvme.a' and
`libc.a'.
`-mads'
On embedded PowerPC systems, assume that the startup module is
called `crt0.o' and the standard C libraries are `libads.a' and
`libc.a'.
`-myellowknife'
On embedded PowerPC systems, assume that the startup module is
called `crt0.o' and the standard C libraries are `libyk.a' and
`libc.a'.
`-mvxworks'
On System V.4 and embedded PowerPC systems, specify that you are
compiling for a VxWorks system.
`-memb'
On embedded PowerPC systems, set the PPC_EMB bit in the ELF flags
header to indicate that `eabi' extended relocations are used.
`-meabi'
`-mno-eabi'
On System V.4 and embedded PowerPC systems do (do not) adhere to
the Embedded Applications Binary Interface (eabi) which is a set of
modifications to the System V.4 specifications. Selecting `-meabi'
means that the stack is aligned to an 8 byte boundary, a function
`__eabi' is called to from `main' to set up the eabi environment,
and the `-msdata' option can use both `r2' and `r13' to point to
two separate small data areas. Selecting `-mno-eabi' means that
the stack is aligned to a 16 byte boundary, do not call an
initialization function from `main', and the `-msdata' option will
only use `r13' to point to a single small data area. The `-meabi'
option is on by default if you configured GCC using one of the
`powerpc*-*-eabi*' options.
`-msdata=eabi'
On System V.4 and embedded PowerPC systems, put small initialized
`const' global and static data in the `.sdata2' section, which is
pointed to by register `r2'. Put small initialized non-`const'
global and static data in the `.sdata' section, which is pointed
to by register `r13'. Put small uninitialized global and static
data in the `.sbss' section, which is adjacent to the `.sdata'
section. The `-msdata=eabi' option is incompatible with the
`-mrelocatable' option. The `-msdata=eabi' option also sets the
`-memb' option.
`-msdata=sysv'
On System V.4 and embedded PowerPC systems, put small global and
static data in the `.sdata' section, which is pointed to by
register `r13'. Put small uninitialized global and static data in
the `.sbss' section, which is adjacent to the `.sdata' section.
The `-msdata=sysv' option is incompatible with the `-mrelocatable'
option.
`-msdata=default'
`-msdata'
On System V.4 and embedded PowerPC systems, if `-meabi' is used,
compile code the same as `-msdata=eabi', otherwise compile code the
same as `-msdata=sysv'.
`-msdata=data'
On System V.4 and embedded PowerPC systems, put small global data
in the `.sdata' section. Put small uninitialized global data in
the `.sbss' section. Do not use register `r13' to address small
data however. This is the default behavior unless other `-msdata'
options are used.
`-msdata=none'
`-mno-sdata'
On embedded PowerPC systems, put all initialized global and static
data in the `.data' section, and all uninitialized data in the
`.bss' section.
`-G NUM'
On embedded PowerPC systems, put global and static items less than
or equal to NUM bytes into the small data or bss sections instead
of the normal data or bss section. By default, NUM is 8. The `-G
NUM' switch is also passed to the linker. All modules should be
compiled with the same `-G NUM' value.
`-mregnames'
`-mno-regnames'
On System V.4 and embedded PowerPC systems do (do not) emit
register names in the assembly language output using symbolic
forms.
`-mlongcall'
`-mno-longcall'
By default assume that all calls are far away so that a longer more
expensive calling sequence is required. This is required for calls
further than 32 megabytes (33,554,432 bytes) from the current
location. A short call will be generated if the compiler knows
the call cannot be that far away. This setting can be overridden
by the `shortcall' function attribute, or by `#pragma longcall(0)'.
Some linkers are capable of detecting out-of-range calls and
generating glue code on the fly. On these systems, long calls are
unnecessary and generate slower code. As of this writing, the AIX
linker can do this, as can the GNU linker for PowerPC/64. It is
planned to add this feature to the GNU linker for 32-bit PowerPC
systems as well.
On Darwin/PPC systems, `#pragma longcall' will generate "jbsr
callee, L42", plus a "branch island" (glue code). The two target
addresses represent the callee and the "branch island". The
Darwin/PPC linker will prefer the first address and generate a "bl
callee" if the PPC "bl" instruction will reach the callee directly;
otherwise, the linker will generate "bl L42" to call the "branch
island". The "branch island" is appended to the body of the
calling function; it computes the full 32-bit address of the callee
and jumps to it.
On Mach-O (Darwin) systems, this option directs the compiler emit
to the glue for every direct call, and the Darwin linker decides
whether to use or discard it.
In the future, we may cause GCC to ignore all longcall
specifications when the linker is known to generate glue.
`-pthread'
Adds support for multithreading with the "pthreads" library. This
option sets flags for both the preprocessor and linker.
Info Catalog
(gcc.info) PowerPC Options
(gcc.info) Submodel Options
(gcc.info) S/390 and zSeries Options
automatically generated by
info2html